Powerplan 90 Series

The Powerplan 90 Series boxes, incorporating advantages of the latest in access floor box design, are manufactured within BS5750 quality environment to meet PSA specification for raised floors MOB-08-801. Carpet trim and lid tray moulded from top quality 'Nylon 66'. Carpet trim reinforced with steel for increased strength. Strong lid tray hinge design ensures reliable lid operation. Lid tray comprises 3mm galvanised steel housed in a moulded tray, thus insulating the steel and avoiding earthing leaks. Strong design of lid lifting handle allows frequent use without failure. 3 and 4 compartment 90 Series access floor boxes are of the same physical size. Carpet trim / lid tray assembly and mounting frame common to both boxes. Box base and grid assembly can be left in floor void with accessory plates pre-wired with flying leads or hard wiring. Carpet trim and lid tray assembly reversible through 180°. Carpet trim and lid tray, a separate assembly, need not be fitted to box base and mounting frame until carpet installation is imminent. Boxes supplied complete in individual cartons. 75mm overall depth of box from top of access floor allows installation in most situations. Standard colour of mouldings is grey, with toning light grey accessory plates. Alternative colours available to order. The 3 and 4 compartment access floor boxes comprise three distinct assemblies - the box base, the mounting frame and the carpet trim / lid tray assembly. The overall dimensions of both units are 344mm X 212mm X 75mm deep. The box base has knockouts in each long side to accept both 20mm and 25mm flexible conduits. These entries can be replaced with grommets to allow cable access. Dividing fillets are provided to separate services. The box base comes complete with a grid to accept a range of interchangeable accessory plates that can either be supplied with or without the respective accessories. The box base and grid are manufactured from galvanised steel. The mounting frame manufactured from galvanised steel is suitable for mounting in a 332mm X 200mm hole cut into any access floor panel with two fixing holes in each long side. The carpet trim / lid tray assembly is manufactured from 'Nylon 66' finished in grey with the carpet trim moulding reinforced with steel. The lid tray assembly is fitted with a strong lifting handle and two cable outlets pivoting on a strong steel section held securely within the moulded lid tray assembly.

3 Compartment Access Floor Box

3 Compartment Floor Outlet Box (Catalogue No. P90-375G)

3 Compartment Plates

All 3 compartment plates are 100mm wide and are fully interchangeable. P301 - 1 twin switched socket 13A P302 - 1 twin unswitched socket 13A P303 - 3 single unswitched socket 13A P302AS - 1 twin unswitched socket 13A American Standard D308 - Plate to accept 2 25pin D sockets D309 - Plate to accept 2 BNC sockets D310 - Plate to accept 2 IBM LAN connectors V311 - Plate to accept 2 LJ3, 2 LJ4 or 2 LJ5 telephone outlets * Not illustrated V305 - Plate to accept 2 LJ2 telephone outlets B306 - Blank plate M307 - Standard BS1363 2 gang piercing

4 Compartment Access Floor Box

4 Compartment Floor Outlet Box (Catalogue No. P90-475G)

4 Compartment Plates

All 4 compartment plates are 75mm wide and are fully interchangeable. P401 - 1 twin switched socket 13A P402 - 1 twin unswitched socket 13A P403 - 3 single unswitched socket 13A V404 - Plate to accept 4 LJ6 telephone outlets or 4 RJ45 data outlets V405 - Plate to accept 2 LJ2 telephone outlets B406 - Blank plate D408 - Plate to accept 2 25pin D sockets D409 - Plate to accept 2 BNC sockets D410 - Plate to accept 2 IBM LAN connectors The supply of non standard plate variations can of course be investigated within the confines of the box. * Non standard and clean earth versions of power plates are available on request.